Connecting to Mayah ISDN
Contents
Configuring the Mayah Sporty to Make an ISDN Call
1.Plug your ISDN line into the codec and attach power.
2.Press "F2 Codec".
3.Press "F3 Setup"
4.Press "F2 Quality"
5.Use the navigation buttons to select an algorithm setting from "G.722", "L2 Mono, Stereo or J-Stereo" or "E apt-X Mono or Stereo", then press the "OK" button to save the setting.
6.Press "F4 ESC" to return to the home screen.
7.Press "F2 Codec", then "F1 Connect", then "F3 Direct".
8.Navigate to "interface" and press "OK" to select ISDN.
9.Navigate to "number1" and press "OK" to enter the ISDN number using the keypad, then press "OK".
10.If you are bonding multiple channels navigate to "number2" and press "OK" to enter the ISDN number using the keypad, then press "OK".
Configuring the Tieline Codec to Dial the Mayah Sporty over ISDN
1.Press the HOME 
button to return to the Home screen and select Connect > ISDN.
2.Navigate to Setup and press the 
button.
3.Select Session Type [Sessionless] > Select Dial Route [None] > Number of B Channels [Choose the number of B-channels (between 1 and 4) required for your connection] > Algorithm [Choose G.722 , E apt-X Mono or Stereo, MP2 Mono or Stereo or MP2 J-Stereo (Note: select 32kHz or 48kHz sample rate for MP2 depending on available B-channels)].
4. Navigate to a Destination (e.g. Dest 1 or Dest 2) and press the button to select each one in turn. Enter the number for each B channel you want to dial and press the button, then select which B channel will dial using that number and press the button.
5.Navigate down to Auto Reconnect and press the button to toggle between Enabled and Disabled. Note: This is normally enabled on the dialing codec only.
6.Navigate down to Save as Program and press the button to save these settings as a program.
7.Navigate down to Module Configuration and press the button.
8.Select the ISDN module you want to configure and press the button.
9.Configure the following settings:
•Accept > Voice and Data
•Network > Check with your Telco (EU-ETSI in Australia; Europe & most countries outside North America; [US Nat] is the most common in the US, but check with your Telco).
•Line Type > Check with your Telco and select either Point-to-Multi (point-to-multipoint) or Point-to--Point (point-to-point).
•DN/MSN > Enter the "SPID" and "DN" numbers if required in your region, e.g. a SPID is normally required in the US.
10. Navigate up to Apply Settings and press the button.
Dialing from the Tieline Codec
Program Dialing
1.If you have saved the ISDN program as previously instructed, press the HOME button to return to the Home screen and select Connect > Programs.
2.Select the saved program you want to load and press the button.
3.Select Load and press the button to load the program.
4.Press the CONNECT 
button to dial the ISDN program connections.
Ad Hoc Dialing
1.If you haven't save the program but have entered the dialing numbers and other settings, press the HOME button to return to the Home screen and select Connect > ISDN > Connect.
2.Press the button to dial using the settings previously entered.
|
Important Note: If you select different algorithm settings on each codec and dial from the Tieline codec, the connection will be unsuccessful and the CONNECTED LED on the front panel of the Tieline codec will continuously flash. Adjust the algorithm settings and attempt to reconnect. |
Dialing from the Mayah Sporty
|
Important Note: Configure ISDN Answer Config settings in the Tieline codec before attempting to dial from the Equinox to the Tieline codec. Select the following settings in the Tieline codec in one of the Configs (see ISDN Answering Configuration for more detail): •May bond. •Sessionless. •Algorithm: G.722, MP2 Mono, MP2 Stereo, MP2 J-Stereo or E apt-X Mono or Stereo. •Sample Rate: 32kHz or 48kHz |
1.Press "F4 ESC" to return to the home screen.
2.Press "F2 Codec", then "F1 Connect", then "F3 Direct".
3.Use the navigation buttons to select "dial" and press the "OK" button to dial all B-channels.